个步骤就是吸气
The first step is to inhale.
接通电源，马达带动轴承支撑的旋转体，当轴承支撑的旋转体的进气侧端面转离了壳之进气口时，在齿沟间的空气被封锁在主、从轴承支撑的旋转体与机壳之间，完成吸气过程。
When the end face of the intake side of the bearing-supported rotator turns away from the intake port of the shell, the air between the teeth grooves is blocked between the main and secondary rotator supported by the bearing and the shell, thus completing the suction process.
第二个步骤就是紧缩
The second step is austerity.
在吸气步骤完毕时，主、从轴承支撑的旋转体齿峰与机壳构成的封锁容积随着轴承支撑的旋转体角度的变化而减少，并按螺旋状挪动，此为“紧缩过程”。
At the end of the suction step, the blockade volume of the rotating body supported by the main bearing and the slave bearing decreases with the change of the angle of the rotating body supported by the bearing, and moves in a spiral shape, which is called "compaction process".
第三个步骤就是紧缩气体与喷油
The third step is to tighten gas and fuel injection.
在第二个过程中，容积不时减少，气体不时被紧缩，压力进步，温度升高，同时，因气压差而变成雾状的光滑被喷入紧缩腔，从而到达紧缩、降低温度密封和光滑的作用。空压机配件颐养维修时对这个环节应该稍加留意。
In the second process, volume decreases from time to time, gas shrinks from time to time, pressure advances and temperature rises. At the same time, smoothness, which becomes foggy due to pressure difference, is sprayed into the contraction chamber, thus achieving the function of tightening, reducing temperature seal and smoothness. Air compressor parts maintenance should pay attention to this link.
第四个步骤就是排气
The fourth step is exhaust.
当轴承支撑的旋转体之封锁齿峰旋转到与机壳排气口相遇时，被紧缩的空气开端排放，直到齿峰与齿沟的吻合面移排气端面，此时齿沟空间为零，即完成排气过程。与此同时，主从轴承支撑的旋转体的另一对齿沟已旋转进气端，构成空间，开端吸气过程，由此开端一个新的紧缩循环。
When the blocking tooth peak of the rotating body supported by the bearing rotates to meet the exhaust port of the casing, the compressed air is discharged at the beginning until the coincidence surface between the tooth peak and the tooth groove moves to the exhaust end surface, and then the space of the tooth groove is zero, that is to say, the exhaust process is completed. At the same time, another pair of teeth grooves of the rotating body supported by the main and slave bearings have been rotated to the intake end, forming the maximum space, starting the suction process, thus starting a new contraction cycle.
当完成以上的步骤后，空压机就曾经完成了，将机械能转换成气体压力能，它会紧接着到个步骤，然后不断循环。我们在运用空压机时，要防止让它长时间超负荷的工作，这样它会呈现过热的状况，从而招致它呈现一些毛病。那关于一些常见的毛病维修，倡议呈现毛病时，找一些的技术人员，停止维修，也能够本人剖析一下详细缘由，然后再对应它的维修措施。
When the above steps are completed, the air compressor has completed the conversion of mechanical energy into gas pressure energy, which will follow the first step, and then continue to circulate. When we use an air compressor, we should prevent it from overloading for a long time, so that it will be overheated, which will cause some problems. When it comes to the maintenance of some common faults, it is advisable to find some professional technicians to stop the maintenance. I can also analyze the reasons in detail, and then correspond to its maintenance measures.
This article is provided by Jinan Air Compressor. Our website is: http://www.jnkbjx.com. We will provide you with high quality service with wholehearted enthusiasm. Welcome to visit!
